Mugen 2 & Mugen 2 Rev.B Compatibility List

[beo21]

hi,

how about the

ASUS P6X58D-E

and

6GB-Triple-Kit Corsair TR3X6G1600C8D DDR3, CL8

heatsinks are higher then standards

best thx

and greetz

[Oli]

The 1-3 (I guess 2) RAM slots closest to the CPU socket will be blocked by the fan. If your case is wide enough you can mount the fan higher on Mugen 2 (this is always the same with those Corsair modules) or you'll have to mount it on the opposite side (sucking) - if you want to use those slots.

Don't know what the backside looks like (because of Mugen 2 backplate). Top side looks ok.

EDIT: As same shops sell the board bundled with Mugen 2 it should be ok.

[beo21]

Originally Posted by Oli

The 1-3 (I guess 2) RAM slots closest to the CPU socket will be blocked by the fan. If your case is wide enough you can mount the fan higher on Mugen 2 (this is always the same with those Corsair modules) or you'll have to mount it on the opposite side (sucking) - if you want to use those slots.

Don't know what the backside looks like (because of Mugen 2 backplate). Top side looks ok.

EDIT: As same shops sell the board bundled with Mugen 2 it should be ok.

red ma halt mal dt.

kannst mal nen link posten bzgl. des BUNLE

ich weiß dass welche die beiden in kombi nutzen,
aber der ram ist der blockiere wie ich meine

wo soll ich den fan hinmontieren

bisher hab ich den fan oben auf meinem andy samurai drauf

grüße aus franken

würde eher diese corsaier nehemn

Corsair XMS3 TR3X6G1600C7 DDR3, CL7 - 6GB-Triple-Kit

sind niedriger und CL7

[Oli]

Intel i7 930 @ 4.0GHz, Asus P6X58D-E Motherboard, 6GB DDR3 1600MHz Overclocked Bundle BU37OC

Der Lüfter kann über normalen RAMs hängen. Bei größeren Heatspreadern hast du zwei Möglichkeiten: Lüfter höher am Mugen befestigen (wenn dein Gehäuse breit genug ist) oder saugend auf der anderen Seite.

Mit den TR3X6G1600C7 wird es praktisch keine Probleme geben. Die sind nur etwas höher als normale RAMs, den Spielraum gibt die Befestigung mit Lüfterklemmen am Mugen 2 auf jeden Fall her.

So oder so - mit schnellem Ein- und Ausbau ist bei Lüftermontage auf der RAM-Seite Ende - hier muss immer erst der Fan ab. Der Sockel ist bei dem Boardlayout und 6 RAM-Slots einfach zu nah.

[StarFyre]

I will try getting the Noctua NC-13 mounting kit today to see if the Mugen 2 rev B will fit on the asus rampage III extreme. Will advise

Sanjay

[bojan1810]

Passt der Mugen 2 auf dieses Mainboard:

www.medionsupport.com/files/8828/manual/7502.pdf

Herzlichen Dank im Voraus für die Antwort.

[StarFyre]

Ok....so the Nocua nc-13 bracket fits the mugen 2 on the asus rampage III extreme.

issue: the screws that came with the mugen 2 are wrong for the clips that need to be attached to it. They can't go into those small holes on the bottom of the heatsink!!!!

Sanjay

[soundklinik]

Fits great, plenty clearance around

[Chike]

Originally Posted by Okiwana Okimoto

Hello elrobbo,

you need to change screw cup and fixing cup =) . You placed both on different side.

RTFM

I am glad to see Scythe take users comments into consideration. The new munting kit is much more practical, and with a rubber washer or two to hold the backplate against the case it may be possible to mount/unmount it without even taking the board out.

Question: is the mounting kit compatible with first rev. and is it possible to order it seperately?

[teum]

Hi,

I tried to install a Mugen 2 rev. B on my Asus P5W DH Deluxe, but there were spots of solder under the backplate preventing it from being completely up against the motherboard.

Does it mean that the Mugen 2 rev. B is incompatible with my motherboard ?