06-04-2010, 10:26 AM
|
Junior Member
Join Date: May 2010
Posts: 4
|
OK, my PSU is mounted at the bottom of my case: http://lian-li.com/v2/tw/product/upl...0f/a70f-05.jpg
It's a Lian Li A70F But can there be compatibility issues with this HDD Rack on top left of the case? |
|
Last edited by Gutgolf; 06-04-2010 at 10:42 AM.. 
|
|
|
06-04-2010, 01:33 PM
|
Senior Member
Join Date: Aug 2007
Location: Germany, in the middle of Europe
Posts: 856
|
Possible. I'd need to overlay cooler, board, case etc with correct dimensions to give you can excat answer but this would need quite an amount of time & work. Which I cannot provide at the moment, sorry.
If Scythe themselves do not comment on this you'll have to try yourself. But it looks rather close! CPU socket is just too close to the edge on this board.
__________________
- All comments relating to mainboard / cooler / case compatibility are based on "best guess". -
- Aussagen zur Kühler-Kompatibilität basieren auf unverbindlicher, persönlicher Einschätzung. - C2D E6700@3.33Ghz@1,28V / Mugen 1, Ret Kit & 2x Slip Stream PWM @ 280rpm |
|
|
|
|
06-04-2010, 10:00 PM
|
Junior Member
Join Date: Jun 2010
Posts: 1
|
Asus M4N98TD EVO Compatability and Backplate
I have two questions. First, is the Mugen 2 Rev. B compatible with the ASUS M4N98TD EVO? Secondly, do I have to remove the stock metal backplate on the motherboard? If you don't know about the M4N98TD EVO could you at least answer the backplate question. I looks like the backplate is mounted using the same holes I would need to mount the Mugen 2 backplate.
Also, do I need to use insulated spacers/washers between the motherboard and the Mugen 2 Rev. B backplate? |
|
Last edited by VikezFan; 06-04-2010 at 10:12 PM.. Reason: More information
|
|
|
06-05-2010, 10:36 AM
|
Junior Member
Join Date: Jun 2010
Posts: 1
|
Asrock Alive Dual eSATA2
Hallo,
auf meinem Asrock Alive Dual eSATA2 passt der Scythe Mugen 2 Rev. B mit Einschränkungen auch. Durch den Lüfter sind die ersten beiden RAM-Slots verdeckt (siehe Bild 2, gelbe Linien). Zur Montage des Kühlers ist das auf dem Mainboard vorhandene Befestigungsmodul für CPU-Kühler zu entfernen. Dazu zieht man die weissen Plastikstifte nach oben, bis sie einrasten. Anschliessend drückt man auf der Rückseite die schwarzen Plastikdübel zusammen und schiebt sie durch die Bohrung. Hört sich schwerer an, als es ist. Da ich nur einen X2 5000+ (65 Watt) kühle, habe ich den Original-Lüfter gegen einen Scythe Slip Stream mit 800 U/Min (SY1225SL12L) getauscht. Vorher hatte ich zuerst einen Arctic Cooling Freezer 64 Pro PWM, anschliessend einen Coolermaster Hyper TX2 (erst mit dem Originallüfter, später mit Enermax Cluster). Die Kühlung war immer ausreichend, aber recht laut. Mit dem Scythe Mugen (mit meiner eigenen "PCGH"-Edition...) habe ich zwar einen hörbaren, aber nicht mehr störenden PC. Noch etwas zur Montage. Ich habe ein Chieftec CS-601. Die Seitentür aus Plexiglas hat normalerweise einen 80er Lüfter. Dieser berührt jedoch die Heatpipeabdeckung des Mugen. Aus diesem Grund habe ich den Lüfter erstmal weggelassen. Leider finde ich keinen schmaleren 80er Lüfter. Alle, die ich fand, haben ca. 2,4 cm Bauhöhe. (siehe Bild 1) Sollte jemand einen schmaleren 80er Lüfter kennen der richtig leise ist, freue ich mich auf einen Tip.  |
|
|
|
|
06-05-2010, 02:19 PM
|
Junior Member
Join Date: Oct 2007
Posts: 18
|
|
|
|
|
|
06-14-2010, 12:40 PM
|
Junior Member
Join Date: Jun 2010
Posts: 1
|
Hi,
will Mugen fit on Asus Crosshair IV formula? http://www.pahing.com/wp-content/upl...-AM3-890FX.jpg |
|
|
|
|
06-19-2010, 04:54 PM
|
Junior Member
Join Date: Jun 2010
Posts: 1
|
Compatibility
Hello everyone,
I received my Scythe Mugen 2 Rev.B today. First, the installation of this Mugen 2 on my micro-ATX ASROCK H55M (LGA1156) is successful, 100% Compatible.  No problem with the VGA Card, there is a 2,5cm space between the Mugen2 and my 4850X2 ! (which is on the first PCI-Express slot)  No problem with the RAM, too. No collision, thanks to my small RAM modules (/!\ Can't install RAM with high heatspreaders) :  Good point : The cooler is just high enough to allow me to change my RAM modules without removing it (I just have to remove the fan). My Core i5 750 @ Stock frequency is at 30°C while idle. NOTE : I think the original Mugen 2 (Rev. A) is compatible with this motherboard TOO, because this mobo has 1156 AND 775 pushpins holes. Nice cooler here. Thanks Scythe ! |
|
Last edited by Cynalynx; 06-19-2010 at 05:35 PM..
|
|
|
06-20-2010, 04:02 PM
|
Junior Member
Join Date: Jun 2010
Posts: 1
|
 Hello everyone, Would the mugen 2 fit on this asus p4p800e deluxe motherboard? Or am I better off with a Samurai ZZ instead? (Price matters, I'm on a small budget) It would be for a p4 prescott 2.8ghz, around 84W TDP, it gets quite hot. Thanks in advance. |
|
|
|
|
06-22-2010, 10:01 PM
|
Junior Member
Join Date: Jun 2010
Posts: 2
|
Msi p55-d85
Hello,
i just installed this beast on my MSI P55-GD85, but i think i'm missing something here. Should there be plastic washers between the mainboard and the metal srews? I haven't seen this in the manual or in the box. The cooler can be moved with a bit of force. Can somebody tell me if i need washers with this mainboard? http://www.postimage.org/image.php?v=gxRdeMA http://www.postimage.org/image.php?v=gxRdhgJ www.postimage.org/image.php?v=gxRdoL9 Thanks for your help! |
|
Last edited by elrobbo; 06-23-2010 at 07:56 AM.. Reason: added picture
|
|
Linear Mode
