Kama Angle Compatibility List

[sumo]

Hello TheQCC,

Thanks for your infos, i add it to our compatibility list.

With which cooler you campared the Kama Angle? intel standard cooler?

Kind Regards
Chris

[Octoploid]

Asus M4A78T-E (AM3 board)

is compatible if you are ready to sacrifice two of the four memory slots.

So it is not an ideal combination, because the CPU socket on this board
is located too far away from the back and the space between the memory
slots and the CPU is too short.

But it works nonetheless.
Temperatures Stock cooler: Idle-44°C Load-56°C
Temperatures Kama Angle: Idle-33°C Load-45°C
(AMD PhenomII X4 955 Processor)

[sumo]

Hello Octoploid,

you can use the red slots, if you use normal memory modules without high heatspreaders.
But thanks for the information you provide to us.

cheers.
chris

[Shockwave]

Asrock M3A790GHX/128M AM3 790GX Motherboard


Compatible


however only standard hight DIMMS in all slots as picture

[Vitali2000]

Sucessfully installed on ga-ma790x-ud4-e in Coolermaster Centurion RC534 Lite silver case. I didn't have any problems installing it and did not even have to put the mainboard outhside the case.

[Passy]

I'd like to add my
Gigabyte GA-MA770-UD3.
It's compatible to the Kama Angle Rev B, but you have to remove the MoBo from you case to apply it and it blocks 2 RAM-Slots.

[badsykes]

hello
I have problems with this board TA790GX A2+
Also i couldn't get the fan installed normally in springs..I have to improvise..
BIG problems installing KAMA ANGLE B on Biostar TA790GX A2+ ... my way of fan installation

BIOSTAR the board ...

i feel stupid really

I beg shockwave to tell how did he fit the cooler on the orange plastic...It was a pain in the ass for me and i feel it doensn't make contact with the CPU.I feel it locks in place a little higher than it should...


Update: OK OK update...I made it after all...After another 2 hour...If i make a combination like position 1 (from down upwards) and position 3 on the other side there is almost no touch with the CPU but i couldn't see that of course.I just felt it with very high temp and freezing..On position 1 + position 2 the temperature sill rised but much slower and after MUCH fighting i could fit 1 + 1 positions.VERY very big effort to put in 1 + 1.This should be made easier because is the default bracket of AM2+ mainboards :S

[phoe]

MSI P35 Neo2 FR/FIR. Compatible









I should rotate the Kama Angle by 180° to mount the fan across, or just buy a bigger chassis, but I am a bit too lazy. :P It working fine in this way I mounted it with E8400@~4GHZ(9x440MHz).
Btw, if you would mount it in same rotation as I did, and put the coller across, it won't block any memory slot, there will be 5mm between fan and memory.(those orange memory that I am using are GEIL 800MHZ ultra)

[EvoBeardy]

Compatible with MSI 785GT-E63:-

In both my old case with top-mounted PSU:-



And perfectly in my CM Storm Scout aswell:-



23c idle on a Phenom II 545 x2 unlocked to full x4 quad-core, 34c running 3DMark Vantage full test (aint run Prime95 since I got the Scout), with an ambient room temp of 25.1c.

Will be upgrading the fan with 1600rpm Slipstream push, and same for a rear pull, or rotate to this-> _l for a Push/Push.
Will post results when I get round to this.

Only the two DIMM slots closest to CPU are inaccessible, but usable with standard height RAMsinks, the 3rd can be accessed only with the fan removed and the outermost is unaffected.

Love this cooler!

Originally Posted by Oli

Very nice review, thanks for sharing it! Still longing for more reviews on Mugen 2 (also in direct comparison with Mugen 1 and Ninja 2).


Cheers, Oli

Still pretty small the list here... can anyone tell if the Angle fits on the MSI P7N SLI Platinum?